Sunday, January 29, 2012

Ubuntu Photo Appliance

I recently decided to resurrect my old fit-PC as a time lapse photography appliance. I'm not sure what I'll wind up doing with it, but the original idea was to mount it on the roof in a weatherproof container and have it photograph the sunrise every day, automatically uploading the images to my web site.

I bought the device in 2008. It was the first model in the fit-PC line, pictured at the bottom of this page from the manufacturer. At the time it was the smallest, cheapest x86 I could find. I had a 1 GB compact flash card from some earlier hacking, and I bought an adapter to use this card as an ATA/IDE hard drive. I had the makings of an embedded server with no moving parts, which I never did anything interesting with for three years.

Anyhow, having not booted the thing in a year or so, I set out to get it working again.

PXE Boot

The last time I set up this system, I used a DD-WRT router to PXE boot from the TFTP server on my Macbook. Did you know that Mac OSX ships with a TFTP server installed? Magical. Unfortunately my current router uses the stock firmware.

While the TFTP server works great, the built-in Mac DHCP/BOOTP server leaves much to be desired. Long story short, I found lots of people on the internet trying to make PXE boot work with it, and none succeeding. I spun my wheels for a few hours, and there's not much else to report on that, except my advice not to try it. This was OSX 10.4 Snow Leopard.

In this age of VirtualBox and high-speed internet, I was able to quickly set up a VM with tftpd-hpa and dhcp3-server. I added and configured a bridged network adapter on eth0, then connected my laptop and the fit-PC to an ethernet switch. Total time: less than 1 hour.
https://help.ubuntu.com/8.04/installation-guide/i386/install-tftp.html

Netboot Installation

I thought I remembered having trouble with newer kernels on this hardware, so my first attempts were with an ancient 8.04 hardy netboot image. This was just about unsupported, and was the oldest release still available from the public mirrors. After a few failed attempts I abandoned it in favor of a command-line install of 11.04 natty, which I was able to get working. Later, after I found that I needed a newer version of the webcam package, I also tried installing 11.10 oneiric. The 3.0 linux kernel would not boot on this hardware, so I recommend staying with natty and linux 2.6.

Natty seemed to install well enough, but I got a "No installable Kernel was found in the defined APT sources" error. I manually installed linux-image-generic as suggested by a forum post.

The first time I tried that, the system wouldn't boot. Not having many other options, I tried it again, and realized that it was running out of disk space. I would never have noticed this without checking the debug screen with Alt+F4 at the end. Apparently 1 GB is not enough for an install of the Ubuntu base system anymore. In any case, it's pretty abysmal that the installer doesn't give you any feedback when you're in this state.

I drove to the closest electronics store for a bigger CF card; there was a single 4 GB model tucked away amidst the SDs and MicroSDs. That installed and booted fine, with linux-image-generic.

I did have to tweak the boot options to skip the splash screen. Press shift to get to the Grub menu on boot.

$ emacs /etc/default/grub
GRUB_CMDLINE_LINUX_DEFAULT="nosplash --verbose text"

$ update-grub

http://ubuntuforums.org/showthread.php?t=1743535
http://ubuntuforums.org/archive/index.php/t-1658718.html

Between the kernel incompatibilities and mysterious problems, I ran the netboot installer about ten times. I kept thinking of the old quote, "The definition of insanity is doing the same thing over and over and expecting different results."

The installer hung occasionally on all three distro versions that I tried. Oneiric segfaulted and somehow corrupted the boot partition after an ill-advised do-release-upgrade from natty. These issues raise the possibility of a hardware problem, but I don't really want to think about that now that it's working. In any case, memtest86 passed, and the CF card is fresh.

Wireless

Wireless was a nightmare when I first started using Linux on my laptop in 2004. I was very happy to see that it has improved enormously since then. For my hardware, it "just worked".

This is my wireless card:

$ hwinfo
34: USB 00.0: 0282 WLAN controller
  [Created at usb.122]
  SysFS ID: /devices/pci0000:00/0000:00:0f.5/usb1/1-4/1-4:1.0
  SysFS BusID: 1-4:1.0
  Hardware Class: network
  Model: "Ralink 802.11 bg WLAN"
  Hotplug: USB
  Vendor: usb 0x18e8 "Ralink"
  Device: usb 0x6238 "802.11 bg WLAN"
  Revision: "0.01"
  Driver: "rt73usb"
  Driver Modules: "rt73usb"
  Device File: wlan0
  Features: WLAN
  Speed: 480 Mbps
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "usb:v18E8p6238d0001dc00dsc00dp00icFFiscFFipFF"
  Driver Info #0:
    Driver Status: rt73usb is active
    Driver Activation Cmd: "modprobe rt73usb"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #32 (Hub)

I installed wireless-tools:

$ iwconfig
wlan0     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on

I was also able to find my wireless network without any issues:

$ sudo ip link set wlan0 up
$ sudo iwlist wlan0 scan
Cell 04 - Address: {redacted}
          Channel:11
          Frequency:2.462 GHz (Channel 11)
          Quality=70/70  Signal level=-40 dBm  
          Encryption key:on
          ESSID:"975B"
          Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
                    24 Mb/s; 36 Mb/s; 54 Mb/s
          Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
          Mode:Master
          Extra: Last beacon: 456ms ago
          IE: IEEE 802.11i/WPA2 Version 1
              Group Cipher : TKIP
              Pairwise Ciphers (2) : CCMP TKIP
              Authentication Suites (1) : PSK
          IE: WPA Version 1
              Group Cipher : TKIP
              Pairwise Ciphers (2) : CCMP TKIP
              Authentication Suites (1) : PSK

The wpasupplicant package is required to connect to my WPA2 network.

$ emacs /etc/network/interfaces
auto wlan0
iface wlan0 inet dhcp
wireless-essid 975B
pre-up wpa_supplicant -B -Dwext -iwlan0 -c/etc/wpa_supplicant.conf
post-down killall -q wpa_supplicant

$ sudo dhclient wlan0
$ ifconfig
wlan0     Link encap:Ethernet  HWaddr {redacted}  
          inet addr:192.168.1.100  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: {redacted}/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:75 errors:0 dropped:0 overruns:0 frame:0
          TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:21576 (21.5 KB)  TX bytes:2476 (2.4 KB)

Horay!


Webcam

I used a midrange webcam, the Logitec c310 HD Webcam. Its chief virtue was that it was available at the Staples down the street, and Google seemed to suggest that it worked under Linux. As with my wireless card, I was cautiously optimistic and ultimately pleased. It also "just worked".

$ hwinfo
35: USB 00.0: 0000 Unclassified device
  [Created at usb.122]
  Unique ID: ADDn.0XCWhgf+Sk0
  Parent ID: k4bc.G_ipYBRd0t3
  SysFS ID: /devices/pci0000:00/0000:00:0f.5/usb1/1-1/1-1:1.0
  SysFS BusID: 1-1:1.0
  Hardware Class: unknown
  Model: "Logitech Unclassified device"
  Hotplug: USB
  Vendor: usb 0x046d "Logitech, Inc."
  Device: usb 0x081b 
  Revision: "0.10"
  Serial ID: "41EDC8E0"
  Driver: "uvcvideo"
  Driver Modules: "uvcvideo"
  Device File: /dev/input/event4
  Device Files: /dev/input/event4, /dev/input/by-id/usb-046d_081b_41EDC8E0-event-if00, /dev/input/by-path/pci-0000:00:0f.5-usb-0:1:1.0-event
  Device Number: char 13:68
  Speed: 480 Mbps
  Module Alias: "usb:v046Dp081Bd0010dcEFdsc02dp01ic0Eisc01ip00"
  Driver Info #0:
    Driver Status: uvcvideo is active
    Driver Activation Cmd: "modprobe uvcvideo"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #32 (Hub)

The streamer package is all you need to grab a screenshot from the command line.

However, I discovered that streamer is broken in 11.04 due to a simple compilation bug. LTS my ass. The package maintainer didn't even test that binary before packaging it up and publishing it to the Canonical repository?

Ultimately, I just downloaded the oneiric version of the package, along with its dependency xawtv-plugins, and manually installed them with dpkg.

In order to use the /dev/video0 device, your user needs to be a member of the video group.
$ sudo gpasswd --add username video

Conclusion

Linux: Still awesome. Still fucked up when you stray from the beaten path.

I love that little fit-PC, and I'm glad it's being put to better use than gathering dust in my closet. Their new models look great too.

On the other hand, if I were starting this project today without a load of old hardware to dispose of, I would probably opt for a used cell phone rather than a semi-embedded x86. The integrated battery, camera, and wireless make for quite a platform. Although I suspect that phone hacking makes for an even more frustrating experience than the one related above.